GEPRC CineLog 35 P 3.5" Cinewhoop Drone HD W/ Avatar – Performance Edition – 6S

The CineLog35 Performance version RTF is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance, and the concept of the Performance version is to maximize Racing performance and achieve perfection with the existing frame size.

Note: Choose Receiver: 

• TBS Crossfire
• ELRS 2.4GHz
• PNP

Note: GoPro and Mount are not included.

VIDEO: GEPRC CineLog 35 Performance

• Comes with two 3D printed parts, which can be installed with GoPro cameras or Naked 8,10 Camera, Insta 360 GO2, and Caddx Peanut cameras
• Walksnail AVATAR HD digital image transmission system makes the FPV image stable and clear and restores true colors and details
• Reversed-motor design with higher flight efficiency, longer flight endurance, and flexible flight attitude
• Equipped with GEPRC F722-45A AIO high-performance FC and integrated BLHeli_S 45A 6S ESC
• 3.5-inch integrated propeller guard hollowed-out weight reduction and noise reduction design
• The GEPRC Team’s Splendid Tuning and the overall flight feel are delicate and flexible
• Shock-absorbing gimbal designs are more stable and clearer shooting
• SPEEDX2 2105.5 motors with DT90-3 propeller

PERFORMANCE EDITION UPGRADES

The CineLog35 Performance version is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance., and the concept of the Performance version is to maximize Racing performance and achieve perfection with the existing frame size. We upgraded the power system, using F722-45A AIO with the new SPEEDX2 2105.5 motor, which has stronger power and faster response speed which makes for easier flying with a GoPro camera and allows you to perform some difficult action flying. You can even Freestyle with GEPRC Naked Hero 8 Camera. Therefore, the CineLog35 Performance can perfectly meet all requirements of aerial photography creators to reach higher-level quality shooting.

WALKSNAIL AVATAR

The Walksnail Avatar HD Camera / VTX Kit features a digital camera and VTX that works with HD Goggles such as the Walksnail Avatar and Fat Shark HD Dominator. This HD VTX combo has lower latency than the competitor at an average of 22ms, with an onboard DVR, 5.8GHz frequency, 8Gb internal storage, and a switchable aspect ratio. 

PRE-TUNED AND PRE-SETUP

This RTF is fully built and test-flown by build technicians at our Florida facility.

• Model: CineLog35 Performance HD Avatar
• Antenna: Walksnail Momoda 5.8Ghz U.FL
• OSD: BetaFlight OSD w/AT7456E chip
• Receiver: PNP /ELRS / TBS Nano RX
• Motor: SPEEDX2 2105.5-2650KV 6S
• Frame: GEP-CL35 Performance
• Camera: Walksnail Avatar
• FC: GEP-F722-45A AIO
• Bottom plate: 2.0mm
• Propeller: HQ DT90-3
• Wheelbase: 142mm
• ESC: BLheli_S 45A
• Arm plate: 3.5mm
• MCU: STM32F722
• Top plate: 2.5mm
• Brand: GEPRC
• Weight: 253g
• VTX: Avatar
• IMU: 6-Axis

IMPORTANT NOTES

• The DJI Remote Controller is recommended for beginners but NOT required to use the FPV System, since you won’t need to set up another receiver. If you don’t have the DJI Remote Controller, you will need a receiver for your transmitter. and then bind to your own radio as usual.
• If you do not have the frsky transmitter, please downgrade the version lower than 2.X.X, www.frsky-rc.com for more details.
• Our current frsky receivers default version in 2.XX, requires us to use of the same version of frsky transmitter. 

• Lumenier N2O Feather-Lite 1550mAh 6S 150c LiPo Battery (XT-60) – 3 Pack Bundle

•   (Insert links such as manuals, firmware, etc)

• 1x GEPRC CineLog 35 P 3.5″ Cinewhoop Drone HD w/ Avatar – Performance Edition
• 2x LiPo Strap (M15x200mm)
• 4x 15-degree damping rings
• 1x 3D Print Antenna Mount
• 2x HQ DT90-3 Propellers
• 2x Battery Silicone Pads
• 1x Fixed Antenna tube
• 2x Landing Pads
• 1x Hardware Kit
• 1x Screwdriver

ADD VIDEO TITLE HERE IN BOLD CAPS

ADD VIDEO TITLE HERE IN BOLD CAPS